Pedaltrain PT-PB3 Pedal-Booster - Triple 10 X5.5 Inches

Used these risers on a vertex tour pro to help clean up some cable routing. The little bit of elevation & flat surface work great to hide some wayward cabling. Bonus points for including appropriately sized screws AND velcro. Would buy again.

Works as advertised. Was worried it would stick up too high but it sits perfectly where you'd want it to for normal sized pedals.

I covered this with velcro and put non-slip rubber strips on the bottom and use it as a mini-pedalboard for two utility pedals that I don't always use. It was perfect for this purpose.

I have had a PedalTrain2 w/hard case for a few years, and two of my favorite pedals were always a little low on the back row. They are a TC Nova Delay and MAXON FL-9 Flanger, and while the TC just needed height, the FL-9 with the Ibanez type switch also needed to be leveled because it was tricky to push down on the actuator at the stock pedaltrain downward angle. These are not cheap pedals, and it was really a bummer that I would have to perform an annoying dance to activate them, and many times would inadvertently hit the knobs of other pedal.Well I just finished installing and testing the Large Pedal booster, and it fit those two pedals perfectly. I was concerned because the Nova delay is fairly wide, but no problem at all. The booster velcro'd in nicely, both pedals fit just fine, and immediately I could use them easier than if they were on the floor because of the added height and fact they are both now level (YES!!). It honestly feels like a new board because all my pedals are equally useable and I no longer have to worry about messing up other settings.And most importantly, my pedalboard still fits perfectly into the hardshell case.You will need to lengthen the connecting cables a bit because of the added distance, but the little bit of work is totally worth the return.All and all, the PedalBooster was well worth the money, and I only wish they had made it a few years back. Highly recommended if you have some pedals that need a little boost or leveling.

Mounted my power supply with this a few years ago and have dragged that pedalboard around quite a bit. No issues.

Worked perfectly with my Pedaltrain Classic JR. Very easy to install. 4 stars for no printed material containing pilot hole drill bit size (I had to guess my way by using increasing bit sizes until the screws tapped). Otherwise an easy install, very solid and does what it should. Installation tips: 1. Take the pedals off your board before installing to make the process easier to manage. 2. Put painter's tape on the board rails and on the Voodoo Labs power supply. Mark the center points on each and line them up to center the power supply on the board. 3. Hold the power supply in place and mark your drill holes on the tape on the board rails with a pen or pencil so they're clearly marked before you drill. 4. Keep the screws holding the brackets to the power supply a little loose so you can "fine tune" placement once the brackets are installed....then make any final adjustments forward or backward and tighten them up.

Bought one of these last month to use as a small pedalboard on its own. I used the included velcro (which, if you let it cure the 24 hours it suggests, works very well) and just slapped some rubber feet on the bottom. Now, I have a small pedal board that fits three MXR-sized pedals (with patch cables) that I can take with me if I don't want or need my full-sized board. While there's no room for a power supply, I'm not disappointed at all. It's small, seems to be made of a sturdy type of metal (I'm guessing aluminum, like all the other Pedaltrains), comes with enough velcro, and most importantly, is only twenty bucks. If you want a small, inexpensive - but sturdy and attractive - pedalboard, just put some rubber feet on this, and I'm sure you'll be happy.

Needed to give my HX Effects some lift on my PT Classic Jr. I’m only using Velcro on the contact points versus screwing it down. Works perfect, but it definitely puts more pressure and bulge on the top of the soft case when zipped shut.

Use them for my Boss DD20 AND Boss MD 500, makes access easier 🎸👍

Originally thought this was an overpriced and pointless accessory. But, I decided to get one after I kept stepping on other pedals controls around my overdrive pedal.This item acts as a perfect adapter for raising the pedal to a better height.I was happily surprised to find that the riser can be fitted with either self tapping screws or with Velcro which allows me to move it around on the board when needed. Both the screws and the Velcro strips are included. I chose to Velcro the riser on to my board and it feels very secure and stable (I gently shook my board upside down to check it’s secure).I’m now considering adding a double width one to allow me to try a different layout for a bigger pedal.

Estupendo material. Incluido el velcro y tornillos. Algo caro probablemente, pero recomendable

OK on the face of it these are pricey for what they are but they work incredibly well. Solid and you know will stand up to years of being stamped on.

Overpriced pieces of metal. Does the job perfectly fine. I rather spend that bucks on it and play music, instead of wasting time on diy. Need to admit it's nicely finished and very sturdy. But construction/idea/fitting - blocks air flows on a side of Voodoo Lab unit - will that affect pawer supply? Time will show. Haven't noticed any overheating problems.Hopefully you can understand it from pics provided - side of the power unit has vents on both sides.Had to drill holes in pedaltrain, fits nicely, holds solid. Can't complain. Happy me ;)I recommend fitting power unit under pedalboards.