Stan's no tube Preventive Liquid Tyre Sealant, 473 ml

Great stuff; been using it for 6 years and have never had to stop during a ride to fix a puncture.

pleased with the sealant, works well. would recommend

very good product

Last year I bought a couple of bikes that came with tubeless tyres which was a first for me after many years of traditional inner tubes. Whilst the alleged benefits of tubeless are well sold, there are a number of counter reason against them as well - not least that its a bit more effort to get them fitted and you need some additional tools and equipment. I managed to avoid doing anything with the tubeless set up for about 6 months but it came to the point that I needed to change one of the tyres and to do this I needed to get some extra bits. For the Tyre Sealant I chose this based on the reviews and price - seemed a good compromise of the two. It's pretty hard to judge what a good sealant is and isn't and I suspect that unless you get a puncture and it either works or doesn't then there's very little to choose between different brands I'll be honest - this was the first time for me fitting a new tubeless tyre and it took a long time and a few dry runs getting the tyre on and off and sealing before I used the sealant. In this case I removed the valve core and used a small syringe whose nozzles fitted inside the valve to inject the recommended quantity. This didn't seem to be too messy. The little bit I spilt on my concrete garage floor has stained it a little though I did lose some of the fluid from the tyre whilst reinflating and getting a seal between the tyre and the rim but it did wipe off the wheel easily. Its been a few weeks now and some rides on the bike and the tyre has not lost any pressure so I'll take that as a positive sign For my road bike tyres this size of bottle would do a good 20 tyres I think On this limited basis I would buy this again

I've tried other brands but keep coming back to Stan's Original sealant.

Great

It works, I've tried lots of different brands of sealant, this one works well enough and it's too expensive.

Good product

excelente funciona muy bien

No tunes, no problems!

very effective. topped up 60ml to my tubeless MTB tire since it's been loosing air and i cannot find any puncture, and have to pump it every 2 days. Since then, i have not pumped my tire and still have same pressure.

I used this to seal the Mavic Yksion Elite All Road tires I purchased here on Amazon for my Diamondback Century 4 Carbon bike. I wanted to go with a tubless setup as I was tired of getting pinch flats from running over sticks and the like on rougher trails. Using it is easy enough. I used this sealant injector that I got here on Amazon: Tubeless Sealant Injector Syringe and Presta Valve Core Removal Tool by KOM Cycling - Designed for Stans No Tubes sealant and other sealants Steps to mount tubeless tires (for road bike/gravel/cross tires, mountain bike is similar but amount of sealant will be about double and pressure to inflate to is around half, just look at the sidewall for max PSI when seating the bead): 1. Make sure your rim is tubeless ready, and seal spokes with Rim Tape if needed. I used Stans No Tubes Rim Tape: Stans No Tubes 10yd x 21mm Rim Tape 2. Install Valve Stems. Get the ones with removable cores; it helps with injecting sealant. I used these 35mm stems from Stans No Tubes: Stans No Tubes 35mm Presta Universal Valve Stem (Carded Pair for Mountain) 3. Install Tire on the rim. Try your best to not use tire levers, as it can mess up the bead on the tire. Tubeless tires typically have a VERY tight bead, to keep the tire from "burping" off the rim. They sell lubrication to get them on, but I just used a bit of soapy water on the one tire...the other one I was able to get on no problem. Tip: Install the label on the tire above the valve stem. It looks clean and helps you easily find the valve to inflate tires. 4. Seat the bead. This is the trickiest part. If you have an air compressor, I'd recommend using it here. You want as much air through the valve stem as possible (remove the valve core at this point). I had to get a special inflator gun for me to get enough air through the valve for it to work. I used this one: TYH Supplies Tire Air Pressure Gun Inflator Gauge with Chuck, PSI / BAR Dual Measurement up to 174 PSI, 1/4-inch Flexible Hose, Accessory Kit, Schrader to Presta Valve Adapter, 20 Valve Caps . If you have problems getting the bead to seat, you can put a tube in, inflate the tube, which will seat both beads; then CAREFULLY remove the tire by popping ONE bead off. This will leave only one bead for the air compressor to seat, and works much easier if you're having difficulty seating both beads at once. 5. Once the bead is set, fill the injector with 2-3 oz. of tire sealant, and inject it through the valve stem. I recommend angling the valve stem so that it's not directly at the bottom of the tire, but rather off to the side, at about 4 oclock or so; this prevents the sealant from wanting to come back out of the valve. 6. Reinstall the valve core, and inflate the tire to close to it's max pressure, typically 70-90 PSI will do the trick. You may hear the tire pop a bit as the bead settles into it's final position. 7. (optional) take bike for a short ride just to make sure the tire is seated okay. I took my bike for maybe a 5 minute, 1 mile ride or so just to quickly ensure they were seated. 8. This is one of the most important steps in my opinion. Get a cardboard box and fold the flaps in so you have a nice, level method of lying the tires on their sides. Lay each tire on its side for 24 hours, to allow the sealant to get into the tiny crevices of the bead. After 24 hours, reinflate, and flip them over to the other side, and wait another 24 hours. Then you should be good to go. After following these steps, my tires have held air incredibly well. I read a lot about how you need to inflate your tires more using a tubeless setup, but my tires have not lost any appreciable amount of pressure in the 3 weeks it's been since I've completed the steps above. If you get a slow leak or it doesn't seem to be sealing well, add another ounce or so of sealant..sometimes it just wants a little more and that's enough to solve the problem. So far I've been super impressed by how well this has worked, and I love the tubeless setup. So much nicer to not have to worry about pinch flats, and I can run 30ish PSI less than I used to without sacrificing efficiency, and the ride quality has improved tremendously. I highly recommend going tubeless if you are on the fence!

Ce produit semble faire correctement son travail car des trous d'épines ont bien été colmatés en toute discrétion...