🌡️ Keep Your Cool with Thermal Grizzly!
The Thermal Grizzly PhaseSheet PTM is a high-performance thermal pad designed for optimal heat transfer in CPUs, GPUs, and other electronic components. With its phase change material, it remains solid at room temperature and only liquefies at 45°C, allowing for easy application. Its non-electrically conductive nature ensures safety for sensitive electronics, while its durability guarantees stable thermal conductivity even after multiple thermal cycles.
I**E
Fantastic for thin laptops that struggle to cool themselves from factory.
My 2019 MacBook Air was ceaselessly thermal throttle and hit its temperature ceiling, even though I swapped the old thermal paste. Applying this to only the CPU die (not the PCH) resolved the issue. It still slows down under maximum load, it quickly stops throttling and the temperatures return to normal. This was easy to apply and, although it’s somewhat pricey, the performance increase is notable and it’s easier to apply than normal paste. At first, the square seems small, but the tiny portion needed for application shows just how much is actually included with this.
R**7
Runs a little warmer than fresh paste, but shouldn't "pump out" like paste does.
This stuff works great, I bought this for my laptop because the Arctic MX-6 paste I have been using rapidly degrades in performance. The initial performance is amazing, but it takes only about a month for it to cool like some old dried out paste that was five years old or something. This product keeps my laptop almost as cool while gaming, but is expected to maintain that performance for a very long time. I had no issues at all installing it for the first time, I suggest reading and following the instructions that are provided for best results. The only thing I wish I had done differently was to have a micrometer to measure the CPU and GPU die size instead of just eyeballing it, and to have a sharper set of scissors to cut the pad down.
S**T
Effective and easy to apply
For the relatively low price, it's really easy to install if you follow the included instructions and so far pretty effective. Once you get a few thermal cycles in, spikes decrease and overall performance increases. On my ryzen 7 9800x3d with a 240mm aio, I'm seeing an average of at least 5°C lower temperatures under load, with my idle temps being around 8°C lower. You can trim the pad to fit your cpu, so it's compatible with pretty much any processor. The packaging kept it perfectly flat too, so no worries on it being folded, not that it would matter much since both sides are covered. Just make sure you follow the instructions and freeze it for a few minutes before you try to work with it, it makes it easier!
S**T
PTM does work, but annoying to apply.
Application was annoying, I put it in the fridge like all tips have said, it really doesn't want to be applied. The red plastic lip made it even harder to apply. PTM should really be used on direct die applications, I used it on my 3060.Temps were the same as the thermal paste when at stressing it on furmark. I did cycle it a few times. At idle the temps were cooler than before by 13 - 15c. It does work, I guess my cooler doesn't have headroom to take advantage of PTM.
M**S
One week so far. (check back after a year)
After a week, this is fantastic. Was using Thermal Grizzly Kryonaut Extreme paste for a year and got 85/67 degrees on my p-cores and 3-cores running cinebench for 10 minutes. After a week with the pad, I am getting 80/63 after 10 minutes. Maybe not a lot to some, but I am highly overclocked.(Just so you know the Kryonaut lowered the temps like 9 degrees over a cheaper paste)No problems installing the pad, Just take your time and use an Exacto knife to help separate the pad. CAREFULLY!
S**9
Drop those gpu deltas
Calmed my alphacooled red devil 7900xtx finally. Easy to use did waste a piece but that was my fault I let it get too warm. Dropped my temp deltas (on water before and after) from 40 to 50c to 20 to 24c. Got me under 70c using high settings with rt on! Highly recommend if it fits like gpu. For for cou paste was good. My original issue was paste push out. This fixed it.
J**Y
Garbage
This thing is hot garbage, I opened up the package and thermal paste was between two pieces of plastic neither said nor top or bottom so I appealed one of the pieces of plastic off and I heard it to my processor I could not get it to stick for nothing nor could I get the second piece of plastic off lifted it up and I can see one small piece starting to lift tried to catch it with my thumb and then folded upon itself and you cannot unfold or unstick it from itself you can't completely useless
K**K
Great thermal conductivity, improved cooling
I installed this in my laptop and the CPU temps are much better, about 20 degrees less. Fans are also much quieter. When installing definitely put it in the fridge for a few minutes otherwise it will risk tearing.
Trustpilot
1 week ago
1 week ago
