IMPRESA 20-Pack of Viking Range - Compatible Grate Rubber Feet Bumpers - Heat-Resistant Material, Works with Many Gas Stove Burner Grates - Equivalent to PD040035 Foot Products

We have a GE Profile stove (the "slate" edition) that after 3 years, the rubber pads beneath the grates became so crushed that the grates no longer sat level. So, after searching through the owner's manual and parts diagrams, I found the correct GE part number. But when I searched for that part number, I discovered that GE was charging an obnoxious amount of money. So, knowing that Viking stoves are pretty much the "cadillacs" of stoves, I thought I would give these a try.No, they did not fit properly onto the GE profile stove. But, if you cut the stem of these pads off with an XACTO knife (keeping the larger diameter "cap", and discarding the stem), you can easily super glue the "caps" onto the top of the existing GE pads - and wahlah your grates will be level again. Plus, you'll have about 14 of these left over, so if these ever crush, you can superglue another one on.Yes, it is definitely redneck engineering - but I refuse to pay 100-times mark-up, on something that costs eight cents to make. (Side note: I used superglue gel, and not regular superglue) Good luck!

Bought a replacement set from a different maker months ago and they’re already trashed because the stem tears off easily. These have a patterned stem that seems more durable. They fit snuggly and don’t fall out when you remove the grate for cleaning. Hope to get longer life from these.

I was delighted to find these at a reasonable price, to replace lost feet from the grates on my 2013 Frigidaire Gallery gas stove. The legs of the pegs fit into the openings, but not snugly, so they'll need to be adhered with some high-heat resistant sealant, which I have on hand. The caps have the same thickness as the ones I'm replacing, so there should be no wobbling of the racks. I'll update this review after I've adhered the feet and used the racks for awhile. The alternative, provided by the manufacturer's customer service, would have cost almost a hundred dollars for 8 pegs - and I need 12. They offered no advice on substitutes. Edited to add: Four months after using the pegs, they've begun to fall out. Maybe I didn't use enough of the sealant, or it couldn't withstand the high heat reached on the gas stovetop burner racks. The sealant had been allowed to cure according to directions. Also, bear in mind: after the tube of sealant had been used and closed tightly, it was extremely difficult to use again after 4 mos. Suggest that if you try these pegs, use plenty of sealant in the holes before inserting them.

I have ordered these feet two times because the heat of cooking causes the rubber to become brittle and break off. I wish these were made of silicone, but they are made from vulcanized rubber. I am using the on a Jenn-Air range and I use the stove daily often with large stock pots simmering for hours. The extended heat time and weight accelerate the decomposition of these feet. If you are cooking occasionally or for relatively short periods of time they will last you longer, possibly years, but for me they are lasting 3-6 months.I saw a suggestion to use RTV silicone to keep the feet from falling out I wouldn't do that. The feet swell slightly after they heat up if you use you stove long enough. You will have to drill out that adhered silicone when you replace the feet and I have never had one of the feet fall out after I used the stove.

Great fit, perfect replacement on a DCS stove. Used a sharp wood screw to get out broken feet.

These worked perfectly for my Frigidaire gas range grates. They stay put without any adhesive, but a dab of red RTV sealant would ensure they don't fall out.

Do not stay in even after wood stove gasket cement. Anybody find somes that fit better?

Product is fine. Disappointment was that delivery instructions were not followed. This is an important aspect to us since that spot was icy and exposed to traffic and theft. Hopefully this will not reoccur and delivery instructions will be followed in the future.